IBM ThinkPad 600X Sep. 25, 2001 ThinkPad BIOS Update Utility Version 1.11 (ITET55WW) ====================================================================== Notice: ------- This program is language independent and can be used with any language system. What This Package Does ---------------------- The ThinkPad BIOS Update Utility given here can update the system program stored in the ThinkPad system to fix problems, add new functions, or expand functions. This release supports the following system: - ThinkPad 600X The supported operating systems are as follows: - Windows 95 OSR2 or later - Windows 98 and 98 Second Edition - Windows Me - Windows NT 4.0 with Service Pack 3 or later - Windows 2000 - Windows XP To determine if you have to update the system program, refer to the "Summary of Change" section. To update the system program, refer to the "Installation instructions" section. Released Versions ----------------- Version 1.00 (ITET44WW) (Initial Release) Version 1.01 (ITET45WW) Support for FlashUpdate A fix for problems as noted below Version 1.02 (ITET47WW) Support for Intel Pentium-III A fix for problems as noted below Version 1.03 (ITET48WW) Version Control Version 1.05 (ITET49WW) A fix for problems as noted below Version 1.06 (ITET50WW) A fix for problems as noted below Version 1.07 (ITET51WW) Version Control Version 1.08 (ITET52WW) Version Control Version 1.09 (ITET53WW) Version Control Version 1.10 (ITET54WW) A fix for problems as noted below Version 1.11 (ITET55WW) A fix for problems as noted below Summary of Changes ------------------ Key: Program Version (for example, 1.00 means Version 1.00) (New) New Function or Enhancement (Fix) Correction to existing function <1.00 - ITET44WW> - (New) Support for TP600X. <1.01 - ITET45WW> - (New) Support for FlashUpdate. - (Fix) System will hung up in reboot time after Windows 95 OSR2.1, USB and other device drivers installed. - (Fix) Linux can't be installed properly or Linux can't boot after updating BIOS. - (Fix) If Windows 98 Second Edition is installed as APM mode and an updated BIOS is installed with a BIOS date 12/02/99 or later, Windows 98SE will change the mode from APM to ACPI whenever a New hardware profile is created. So this BIOS set the date to 11-30-99. Note: If you apply the APMINST.REG (http://www.pc.ibm.com/support/qtechinfo/MIGR-48VPPW.html), Mode Changing from APM to ACPI does not occur. <1.02 - ITET47WW> - (New) Support for a new revision of Intel Pentium III. - (Fix) Intermittent hang when Docked for the first time. <1.03 - ITET48WW> - Version Control <1.05 - ITET49WW> - (New) Support for a new revision (C0-Step) of Intel Pentium III. - (Fix) System can not boot with the HDD that consumes all root directory. <1.06 - ITET50WW> - (Fix) Windows 2000: System rarely hangs with connection/disconnection of AC adapter. <1.07 - ITET51WW> - Version Control <1.08 - ITET52WW> - Version Control <1.09 - ITET53WW> - Version Control <1.10 - ITET54WW> - (Fix) Linux system fail with memory size detection. Linux OS only. <1.11 - ITET55WW> - (New) Windows XP Support - (Fix) OS installation failure with CD-ROM boot Installation Instructions ------------------------- Notes: - You need an AC adapter and a charged battery pack to update the system program. - If your computer is attached to any kind of port replicator, turn off the computer and detach it before proceeding. - Before using Flash Update with Windows 98 Second Edition, IBM recommends that you download and apply the "Windows 98 Second Edition Shutdown Supplement" from the Microsoft Support WWW Site. This supplement and information regarding this supplement can be found at: http://support.microsoft.com/support/kb/articles/Q239/8/87.ASP 1. After you have opened the above link, click on http://www.microsoft.com/windows98/downloads/corporate.asp 2. Scroll down to Windows 98 Second Edition Shutdown Supplement and click on it. 3. Click Next. 4. Accept the License to download the file. 5. Run the executable that you just downloaded. 1) Print these instructions or display on another computer. 2) Firmly connect the AC adapter to the computer. 3) Start Windows 95/98/Me/2000 or Windows NT 4.0 on the target computer. 4) Make the temporary directory on the hard drive (for instance, C:\Temp) 5) Download the Embedded Controller Program Update Utility from the web site and store the file into the temporary directory. (e.g. C:\Temp) 6) Click on Start button. 7) Click on Run. 8) Specify filename with the full path name where you stored Embedded Controller Program Update Utility. (e.g. C:\Temp\ituj10us.exe) Then press Enter. 9) Follow the instructions. 10) When completed, system is automatically turned off. Warning: Do not turn off or suspend the computer until the update has been completed. IF YOU TURN OFF OR SUSPEND THE COMPUTER WHILE THE UPDATE IS STILL IN PROGRESS, THE SYSTEM BOARD MAY HAVE TO BE REPLACED. After the update has been completed, do the following to confirm the change is correctly applied. 6. Make sure there is no diskette inserted in the diskette drive. 7. Turn on the computer; then, while the Press F1 for IBM BIOS Setup Utility message is displayed at the lower-left area of the screen, press F1 key. If a password prompt appears, type the correct password. 8. Check version. BIOS Information ---------------- Each version of the ThinkPad BIOS Update Utility contains the following system program (BIOS). The BIOS Version and the date can be viewed by invoking IBM BIOS Setup Utility. BIOS version number can be viewed by running ThinkPad Configurator from your operating system and select System Information from the Help menu or System Information button. BIOS information can also be found by invoking IBM BIOS Setup Utility. BIOS BIOS Slave controller Slave controller Version Date Version Date -------------- -------- ---------------- ---------------- 1.00 ITET44WW 12-21-99 1.10 IHHT10WW 10-08-99 1.01 ITET45WW 11-30-99 1.10 IHHT10WW 10-08-99 1.02 ITET47WW 11-30-99 1.10 IHHT10WW 10-08-99 1.03 ITET48WW 11-30-99 1.10 IHHT10WW 10-08-99 1.05 ITET49WW 11-30-99 1.10 IHHT10WW 10-08-99 1.06 ITET50WW 11-30-99 1.10 IHHT10WW 10-08-99 1.07 ITET51WW 11-30-99 1.10 IHHT10WW 10-08-99 1.08 ITET52WW 11-30-99 1.10 IHHT10WW 10-08-99 1.09 ITET53WW 11-30-99 1.10 IHHT10WW 10-08-99 1.10 ITET54WW 11-30-99 1.10 IHHT10WW 10-08-99 1.11 ITET55WW 11-30-99 1.10 IHHT10WW 10-08-99 Memory information ------------------ The following information shows memory areas that are either unavailable or that can be included with a memory manager such as EMM386. Reserved BIOS Area: C0000-CBFFF (reserved for Video BIOS) F0000-FFFFF (reserved for BIOS) Usable BIOS ROM Area* E0000-EFFFF (can be used as UMB (Upper Memory Block)) Simple Boot Flag function ------------------------- This function automatically optimizes the behavior and boot performance of the BIOS and operating system, based on the installed operating system and previous boot. If this function is Enabled and once a Plug and Play-capable operating system, such as Windows 98, is installed, the system BIOS does not configure such hardware resources as system interrupts, memory ranges, and I/O port ranges for all the devices in the system. If you are going to use a non-Plug and Play-capable operating system, disable this function so that the BIOS will configure hardware resources. (Important Notice) If you are using multiple operating systems in addition to Windows 95/98, you must DISABLE the Simple Boot Flag in Easy-Setup. To modify the Simple Boot Flag: 1. Hold down the F1 key on the ThinkPad and power on the system. 2. Open the Config icon. 3. Open the Quick Boot icon. 4. Set Simple Boot Flag to Enable or Disable depending on configuration. Windows 2000 diskette drive/drive letter handling ------------------------------------------------- Diskette drive/drive letter handling under Windows 2000 environment is changed to fixed drive letter assignment. External diskette drive letter : A drive (A:) Ultraslim Bay diskette drive letter : B drive (B:) Since Windows 2000 will assign drive letter A for an FDD found first, and it may vary. Boot Menu ---------- When this option is enabled a startup Boot Menu will appear allowing you to choose the bootable device. This function is enabled or disabled via the Easy Setup option in BIOS. Enabling or disabling the Boot Menu: 1. Power off the system. 2. Press and hold the F1 on the ThinkPad keyboard, and power on the system. This will bring up the Easy Setup menu screen. 3. Click the Config icon. 4. Click the Boot Menu F12 icon. 5. Select enable or disable and click OK. 6. Click Exit to leave the Config menu. 7. Click Startup, then click Power-on. 8. If any items are selected, these are the items that will appear in the Startup Menu. If no items are selected, all startable items will appear in the menu. 9. Click OK to close the Startup devices selection list. 10. Click Exit to close the startup mode selection list. 11. Click Restart then OK to restart the system. To display the Start Menu 1. Shutdown the system so that it is powered off. 2. Press and hold the F12 key while powering on the system. The Boot Menu should appear. Use the up and down arrow keys to select the boot device. Known Limitations <=== This paragraph is valid at Win95 support. ----------------- 1. To execute this package on Windows 95, the following modules are required: - MSVCRT.DLL - MFC42.DLL Trademarks ---------- * IBM and ThinkPad are trademarks of IBM Corporation in the United States. * Intel and Pentium are trademarks of Intel Corporation. * Windows is a trademark of Microsoft Corporation. * Linux is a registered trademark of Linus Torvalds. Other company, product, and service names may be registered trademarks, trademarks or service marks of others.